Search

Shopping Cart
Your cart is empty.



Browse Categories
Model, Year, and Engine

C2569-1J, 1" Motor Mount Lifts, Classic Polyurethane


Price: $89.95
Part Number: C2569-1J
Includes: Everything shown plus 1 sticker
Made in USA: Using USA steel, bushings, hardware, etc.
Warranty: Lifetime - Except bushings
1991-1995 2.5L YJ Wrangler Jeep 1" Motor Mount Lifts (Pair)
Want Jeep motor mount lifts (MMLs) to help correct driveline angle caused by an extreme suspension lift? Doing a tummy tuck or other modification that's impacting drive-line angle? Brown Dog designed these MML to reposition your engine one inch higher than stock (at the cooling fan). This modification results in a change in the driveline angle. You'll find these mounts a serious upgrade from most aftermarket mounts, too.
 
Engineered for High Performance.
We use steel and feature double-weld joints to provide the most strength possible. This is significantly stronger than the "strap" design commonly found on lower-strength original and many aftermarket mounts. And, just to test the strength of our mounts, we periodically pull a pair off the shelf and put them through our 20-Ton Press Test. We have yet to see a Brown Dog MM or MML with a structural failure. Nor have we had even one customer report a break of the steel mount.
 
Bolt-In Design.
This pair of motor mounts features a slightly narrower mount for installation on the driver (left) side than the right (passenger) side. The left mount will to slide into the original left bracket with no modification to either the bracket or the mount. The right mount is wider than the left side, but not quite as wide as the original right mount. We ship shims with this mount for use with the original right bracket. We do not make a wide motor mount for the right side because the original right cast-aluminum bracket will break, (it's a matter or when, not if) regardless if you're using our mounts or orginal mounts. This right mount is the same width as 2.5L Jeep motor mounts vehicles built after 1996. It slides into the Brown Dog right bracket.
  

Featuring Classic Polyurethane Bushings.

The Classic Polyurethane bushings in this set of Brown Dog motor mounts will give your rig a sportier feel. If the bushings ever wear out, replacements are available from Brown Dog Offroad. Prefer Ultra-Flex Rubber bushings? We offer all motor mounts and motor mount lifts with either polyurethane or rubber to match your preference. Not sure which is for you? Click here.

 

Backed by Brown Dog Promise.
Brown Dog motor mounts will be the last set of mounts you'll need. The Brown Dog gives you his promise.

 

Free Shipping.
All products ship free to all USA and APO/FPO addresses. International customers pay reasonable shipping fee. Never a "handling fee." Click here for shipping policy.   

 

Installation Notes

  • Engine lifted 1" at stock cooling fan.
  • On 1991-1995 2.5L YJ, the right (passenger side) mount bolts to a cradle which, in turn, bolts to pylon (aka perch or frame-side bracket). If in good condition, you may wish to reuse your existing cradle. However, many customers have removed the mount to replace it and then saw the cast cradle busted into a couple pieces. You may want to order a CR2569 Motor Mount Cradle with your motor mounts.
  • Carefully inspect original engine brackets (right side is typically cast aluminum and prone to break) for any excess wear, especially cracks. The original brackets weren't designed to handle the strength of these high-performance motor mounts. If only the right (passenger side) bracket needs replaced, order B2569-R bracket with these mounts. If you'd rather upgrade all the engine brackets, motor mounts and cradle at once, order the X2569-1 Kit which includes motor mounts, engine brackets, and the passenger mount support cradle.
  • Tighten through-bolts (bolt that goes through bracket arms and motor mount) snug. (Do NOT over-tighten!)
  • Bolts to pylons should be tightened like most others on your Jeep frame. Nice and tight. 
  • If you have any questions during installation do NOT alter the part. Instead, call Brown Dog, 866 401-3877. We have extended support to assist with installation.

Application Notes.
Please call 866-401-3877 or email info@browndogindustries.com for assistance.

  • Jeep Wrangler YJ, 2.5L, 4 Cylinder, 1991-1995

 

 

 

 

Frequently purchased with this

CR2569, Cradle, Motor Mount - Frame Bracket
Cradle bolts between passenger motor mount and pylon. Also called a motor mount frame-side bracket. Prone to breaking, stamped steel originals are difficult to find. Use with original strap-style or Brown Dog motor mounts. Made in USA. One per vehicle.
Price: $39.95
CR2569, Cradle, Motor Mount - Frame Bracket
B2569-R, Engine Bracket, Right
Original cast aluminum brackets prone to break. Impossible to locate. All-steel passenger-side bracket accepts original strap-style or Brown Dog motor mounts. Fits 1991 and up 2.5L I4 Jeep YJ, TJ, XJ, or MJ. Grade 8 hardware included. Made in USA.
Price: $114.95
B2569-R, Engine Bracket, Right